California Instruments 2003RP AC Power Source
Programmable AC Power Source 2000VA
Controller Capabilities
The RP Series uses a
precision digital sinewave generator to produce a low distortion output
. Dual LCD readouts clearly display programmed settings for voltage,
current limit and frequency. Load current is measured using true RMS
sensing and can be displayed on the front panel as well. Adjusting
voltage, frequency and current limit is accomplished using a set of
digitally encoded rotary knobs. For ATE applications, both IEEE-488 and
RS232C interfaces are available as an option.
Applications
The wide output frequency range of 16 Hz to 500 Hz (801RP and 1251RP)
or 16 Hz to 5000 Hz (2001RP and 2003RP) make the RP Series suitable
sources for both commercial and avionics applications. Dual voltage
ranges provide maximum output current at any programmed voltage up to
270 Volt (801RP, 1251RP and 2003RP) or 300 Volt (2001RP). The built in
rms. current measurement function eliminates the need for external
current shunts or transformers to monitor load current. For front panel
operation, the RP Series features simple and intuitive controls for
setting voltage, frequency and current limits. Current drawn by the
load can be read directly on the large LCD display with 100 mA
resolution (801RP and 1251RP) or 1 mA resolution (2001RP and 2003RP).
With the addition of the RS232C and IEEE-488 interface option, the RP
Series sources can be used in automated test environments. Since the RP
Series offers a high power to size ratio, requiring limited rack
height, they can be used to upgrade existing ATE stations or build new
ones.
The 2003RP provides three phase output and is a very cost
effective AC power source for Avionics applications, especially in the
-AV version.
The included PC control program (requires -IF option
for 801RP and 1251RP or -OP1 option for 2001RP and 2003RP) supports
transient generation to simulate real-world AC line conditions like
brown-outs, voltage sags, surges and frequency fluctuations.
Remote Control
The
optional remote control interface allows complete control of all AC
source functions and provides measurement data to the controller. This
allows the RP Series AC source to be used as a low cost AC test system.
A Windows� Graphical User Interface (GUI) program is included with the
interface option. Automatic power cycling and transient generation is
made possible with the use of this GUI program. The GUI output control,
measurement and transient screens are shown here. For quality assurance
applications, measured voltage, current and VA readings can be logged
to disk for documentation and analysis purposes. All data recorded is
time stamped to create a complete history of each test run.
Up to
eight often used front-panel setups can be stored in non-volatile
memory for quick recall from the PC controller through the interface.
If needed, the front panel can be locked out to prevent operator
intervention during test runs.
The 2001RP and 2003RP offer
additional features over the bus such as the ability to select the
turn-on or turn-off phase angle of the output voltage. This capability,
combined with the peak current measurement function, enables inrush
current analysis of a unit under test.
AC Transient Generation
Transient programming is supported by the GUI program with user defined
transient lists of up to 100 steps. Available transient functions are
voltage step, voltage drop, voltage sweep, voltage surge/sag, frequency
step, frequency sweep, frequency surge/sag as well as functions that
combine both voltage and frequency changes. The intuitive Windows �
interface greatly facilitates creating and storing often used transient
programs. Transient programs can be recalled from disk and executed
once, continuously or a specified number of times. Editing functions
such as delete and insert make it easy to modify or expand existing
programs. This capability makes it easy to evaluate products for
immunity to common AC line disturbances such as brownouts, surges,
swells, sags and frequency variations.
Our sales representatives will be happy to provide you with the most up-to-date information about the Cal Instruments 2003RP , as well as helping you find the product solution that fits your needs. If you are interested in the residual market value for the Cal Instruments 2003RP, please contact us to sell your equipment. Whether you are looking to liquidate unused assets or resell equipment, we buy Cal Instruments 2003RP and all types of test equipment at the best price.
- Model: 2003RP
- Manufactured by: California Instruments
![TEC [home link]](includes/templates/tecstore/images/logo.jpg "TEC [home link]"){kind=logo}
|
|
USA & Canada: (800) 615-8378
Mexico 52-55-8421-4127
Chile: 2-897-4335
Brazil: 301-32793
United Kingdom: 20-8144-7837
Sweden: 46-46-288-61-42
Denmark: 369-92915
Finland: 358-9-2316-3837
Estonia: 712-3440 
China: 86-755-8355-2154
Hong Kong: 852-2690-1360
Australia: 61-2-8011-3687